svcadm(1M)을 검색하려면 섹션에서 1M 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
in.ripngd(8)
System Administration Commands in.ripngd(8)
NAME
in.ripngd - network routing daemon for IPv6
SYNOPSIS
/usr/lib/inet/in.ripngd [-s] [-q] [-t] [-p n] [-P] [-v] [logfile]
DESCRIPTION
in.ripngd is the IPv6 equivalent of in.routed(8). It is invoked at boot
time to manage the network routing tables. The routing daemon uses the
Routing Information Protocol for IPv6.
in.ripngd is managed by the service management facility (SMF), by means
of the service identifier:
svc:/network/routing/ripng:default
In normal operation, in.ripngd listens on the udp(4P) socket port 521
for routing information packets. If the host is an internetwork router,
it periodically supplies copies of its routing tables to any directly
connected hosts and networks.
When in.ripngd is started, it uses the SIOCGLIFCONF ioctl(2) to find
those directly connected IPv6 interfaces configured into the system and
marked "up"; the software loopback interface is ignored. If multiple
interfaces are present, it is assumed the host will forward packets
between networks. in.ripngd then multicasts a request packet on each
IPv6 interface and enters a loop, listening for request and response
packets from other hosts.
When a request packet is received, in.ripngd formulates a reply based
on the information maintained in its internal tables. The response
packet contains a list of known routes. With each route is a number
specifying the number of bits in the prefix. The prefix is the number
of bits in the high order part of an address that indicate the subnet
or network that the route describes. Each route reported also has a
"hop count" metric. A count of 16 or greater is considered "infinity."
The metric associated with each route returned provides a metric rela‐
tive to the sender.
The request packets received by in.ripngd are used to update the rout‐
ing tables if one of the following conditions is satisfied:
o No routing table entry exists for the destination network or
host, and the metric indicates the destination is "reach‐
able", that is, the hop count is not infinite.
o The source host of the packet is the same as the router in
the existing routing table entry. That is, updated informa‐
tion is being received from the very internetwork router
through which packets for the destination are being routed.
o The existing entry in the routing table has not been updated
for a period of time, defined to be 90 seconds, and the
route is at least as cost-effective as the current route.
o The new route describes a shorter route to the destination
than the one currently stored in the routing tables; this is
determined by comparing the metric of the new route against
the one stored in the table.
When an update is applied, in.ripngd records the change in its internal
tables and generates a response packet to all directly connected hosts
and networks. To allow possible unstable situations to settle, in.rip‐
ngd waits a short period of time (no more than 30 seconds) before modi‐
fying the kernel's routing tables.
In addition to processing incoming packets, in.ripngd also periodically
checks the routing table entries. If an entry has not been updated for
3 minutes, the entry's metric is set to infinity and marked for dele‐
tion. Deletions are delayed an additional 60 seconds to ensure the
invalidation is propagated throughout the internet.
Hosts acting as internetwork routers gratuitously supply their routing
tables every 30 seconds to all directly connected hosts and networks.
OPTIONS
in.ripngd supports the options listed below. Listed with the options
are the equivalent SMF property values. These are set for the
ripng:default service with a command of the form:
# routeadm -m ripng:default key=value
-p n Send and receive the routing packets from other routers using
the UDP port number n. Use of this option is equivalent to set‐
ting the udp_port property.
-P Do not use poison reverse. Use of this option is equivalent to
setting the poison_reverse property to false.
-q Do not supply routing information. Use of this option is equiv‐
alent to setting the quiet_mode property to true.
-s Force in.ripngd to supply routing information whether it is
acting as an internetwork router or not. Use of this option is
equivalent to setting the supply_routes property to true.
-t Print all packets sent or received to standard output. in.rip‐
ngd will not divorce itself from the controlling terminal.
Accordingly, interrupts from the keyboard will kill the
process. Not supported by the ripng service.
-v Print all changes made to the routing tables to standard output
with a timestamp. Use of this option is equivalent to setting
the verbose property to true.
Any other argument supplied to this option is interpreted as
the name of the file in which the actions of in.ripngd, as
specified by this option or by -t, should be logged instead of
being sent to standard output.
The logfile can be specified for the ripng service by means of
the log_file property.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Availabilitysystem/network/routing
SEE ALSO
ioctl(2), udp(4P), attributes(7), smf(7), in.routed(8), routeadm(8),
svcadm(8)
G. Malkin, R. Minnear, RFC 2080, RIPng for IPv6, January 1997.
NOTES
The kernel's routing tables may not correspond to those of in.ripngd
for short periods of time while processes that utilize existing routes
exit; the only remedy for this is to place the routing process in the
kernel.
in.ripngd currently does not support all of the functionality of
in.routed(8). Future releases may support more if appropriate.
in.ripngd initially obtains a routing table by examining the interfaces
configured on a machine. It then sends a request on all directly con‐
nected networks for more routing information. in.ripngd does not recog‐
nize or use any routing information already established on the machine
prior to startup. With the exception of interface changes, in.ripngd
does not see any routing table changes that have been done by other
programs on the machine, for example, routes added, deleted or flushed
by means of the route(8) command. Therefore, these types of changes
should not be done while in.ripngd is running. Rather, shut down
in.ripngd, make the changes required, and then restart in.ripngd.
Oracle Solaris 11.4 11 May 2021 in.ripngd(8)