svcadm(1M)을 검색하려면 섹션에서 1M 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
cfgadm_scsi(8)
System Administration Commands cfgadm_scsi(8)
NAME
cfgadm_scsi - SCSI hardware specific commands for cfgadm
SYNOPSIS
/usr/sbin/cfgadm [-f] [-y | -n] [-v] [-o hardware_option]
-c function ap_id...
/usr/sbin/cfgadm [-f] [-y | -n] [-v] [-o hardware_option]
-x hardware_function ap_id...
/usr/sbin/cfgadm [-v] [-a] [-s listing_option] [-o hardware_option]
[-l [ap_id | ap_type ... ]]
/usr/sbin/cfgadm [-v] [-o hardware_option] -t ap_id...
/usr/sbin/cfgadm [-v] [-o hardware_option] -h [ap_id]...
DESCRIPTION
The SCSI hardware specific library /usr/lib/cfgadm/scsi.so.1
provides the functionality for SCSI hot-plugging through the
cfgadm(8) command. cfgadm operates on attachment points, which are
locations in the system where hardware resources can be dynamically
reconfigured. For information regarding attachment points, see the
cfgadm(8) man page.
For SCSI hot-plugging, each SCSI controller is represented by an
attachment point in the device tree. In addition, each SCSI device is
represented by a dynamic attachment point. Attachment points are named
through ap_ids. Two types of ap_ids are defined: logical and physical.
The physical ap_id is based on the physical pathname, whereas the logi‐
cal ap_id is a shorter more user-friendly name. For SCSI controllers,
the logical ap_id is usually the corresponding disk controller number.
For example, a typical logical ap_id would be c0.
SCSI devices are named relative to the controller ap_id. Thus if a disk
device is attached to controller c0, its ap_id can be:
c0::dsk/c0t0d0
where dsk/c0t0d0 identifies the specific device. In general, the device
identifier is derived from the corresponding logical link for the
device in /dev. For example, a SCSI tape drive logical ap_id could be
c0::rmt/0. Here c0 is the logical ap_id for the SCSI controller and
rmt/0 is derived from the logical link for the tape drive in /dev/rmt.
If an identifier can not be derived from the link in /dev, a unique
identifier will be assigned to it. For example, if the tape device has
no link in /dev, it can be assigned an ap_id of the form c0::st3 where
st3 is a unique internally generated identifier.
When a controller is capable of supporting the Oracle Solaris I/O mul‐
tipathing feature (formerly known as MPxIO or the Sun StorEdge Traffic
Manager [STMS]) and is enabled, the controller provides a path to a
scsi_vhci(4D) multipath device. If a device attached to such a con‐
troller is supported by scsi_vhci(4D), its ap_id can be:
c0::0,0
...where 0,0 uniquely identifies the target and logical unit informa‐
tion. The Type field for a path of such ap_ids indicates if it repre‐
sent a path to the scsi_vhci(4D) multipath devices, along with the type
of device that is connected to through the path.
A simple listing of attachment points in the system will include
attachment points at SCSI controllers but not SCSI devices. Use the -a
flag to the list option (-l) to list SCSI devices as well. For example:
# cfgadm -l
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
sysctrl0:slot0 cpu/mem connected configured ok
sysctrl0:slot1 sbus-upa connected configured ok
To list SCSI devices in addition to SCSI controllers:
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t14d0 disk connected configured unknown
c0::dsk/c0t11d0 disk connected configured unknown
c0::dsk/c0t8d0 disk connected configured unknown
c0::dsk/c0t0d0 disk connected configured unknown
c0::rmt/0 tape connected configured unknown
sysctrl0:slot0 cpu/mem connected configured ok
sysctrl0:slot1 sbus-upa connected configured ok
If the controller c0 was enabled with the Oracle Solaris I/O multi‐
pathing and the connected disk and tape devices are supported by the
Oracle Solaris I/O multipathing the output would be:
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::11,0 disk-path connected configured unknown
c0::14,0 disk-path connected configured unknown
c0::8,0 disk-path connected configured unknown
c0::0,0 disk-path connected configured unknown
c0::a.0 tape-path connected configured unknown
sysctrl0:slot0 cpu/mem connected configured ok
sysctrl0:slot1 sbus-upa connected configured ok
Refer to cfgadm(8) man page for more information regarding listing
attachment points. The receptacle and occupant state for attachment
points at the SCSI controller have the following meanings:
empty
not applicable
disconnected
bus quiesced (I/O activity on bus is suspended)
connected
bus active
configured
one or more devices on the bus is configured
unconfigured
no device on the bus is configured
The corresponding states for individual SCSI devices are:
empty
not applicable
disconnected
bus to which the device is attached is quiesced
connected
bus to which device is attached is active
configured
device or path to a multipath SCSI device is configured
unconfigured
device or path to a multipath SCSI device is not configured
OPTIONS
cfgadm defines several types of operations besides listing (-l).These
operations include testing, (-t), invoking configuration state changes,
(-c), invoking hardware specific functions (-x), and obtaining configu‐
ration administration help messages (-h).
-c function
The following generic commands are defined for the SCSIhardware
specific library:
For SCSI controller attachment points, the following configuration
state change operations are supported:
connect
Unquiesce the SCSI bus.
disconnect
Quiesce the bus (suspend I/O activity on bus).
Incorrect use of this command can cause the system to hang. See
NOTES.
configure
Configure new devices on SCSI bus.
unconfigure
Unconfigure all devices connected to bus.
The following generic commands are defined for SCSI devices and for
paths to multipath SCSI devices:
configure
Configure a specific device or a specific path to a multipath
SCSI device.
unconfigure
Unconfigure a specific device or a specific path to a multipath
SCSI device.
-f
When used with the disconnect command, forces a quiesce of the SCSI
bus, if supported by hardware.
Incorrect use of this command can cause the system to hang. See
NOTES.
-h ap_id
SCSI specific help can be obtained by using the help option with
any SCSI attachment point.
-o hardware_option
No hardware specific options are currently defined.
-s listing_option
Attachment points of class scsi can be listed by using the select
sub-option. Refer to the cfgadm(8) man page for additional informa‐
tion.
-t ap_id
No test commands are available at present.
-x hardware_function
Some of the following commands can only be used with SCSI con‐
trollers and some only with SCSI devices.
In the following, controller_ap_id refers to an ap_id for a SCSI
controller, for example, c0. device_ap_id refers to an ap_id for a
SCSI device, for example: c0::dsk/c0dt3d0.
The following hardware specific functions are defined:
insert_device controller_ap_id
Add a new device to the SCSI controller, controller_ap_id.
This command is intended for interactive use only.
remove_device device_ap_id
Remove device device_ap_id.
This command is intended for interactive use only.
replace_device device_ap_id
Remove device device_ap_id and replace it with another device
of the same kind.
This command is intended for interactive use only.
reset_device device_ap_id
Reset device_ap_id.
reset_bus controller_ap_id
Reset bus controller_ap_id without resetting any devices
attached to the bus.
reset_all controller_ap_id
Reset bus controller_ap_id and all devices on the bus.
locator [=on|off] device_ap_id
Sets or gets the hard disk locator LED, if it is provided by
the platform. If the [on|off] suboption is not set, the state
of the hard disk locator is printed.
led[=LED,mode=on|off|blink] device_ap_id
If no sub-arguments are set, this function print a list of the
current LED settings. If sub-arguments are set, this function
sets the mode of a specific LED for a slot.
EXAMPLES
Example 1 Configuring a Disk
The following command configures a disk attached to controller c0:
# cfgadm -c configure c0::dsk/c0t3d0
Example 2 Unconfiguring a Disk
The following command unconfigures a disk attached to controller c0:
# cfgadm -c unconfigure c0::dsk/c0t3d0
Example 3 Adding a New Device
The following command adds a new device to controller c0:
# cfgadm -x insert_device c0
The system responds with the following:
Adding device to SCSI HBA: /devices/pci@8,700000/scsi@1
This operation will suspend activity on SCSI bus c0
Continue (yes/no)?
Enter:
y
The system responds with the following:
SCSI bus quiesced successfully.
It is now safe to proceed with hotplug operation.
Enter y if operation is complete or n to abort (yes/no)?
Enter:
y
Example 4 Replacing a Device
The following command replaces a device attached to controller c0:
# cfgadm -x replace_device c0::dsk/c0t3d0
The system responds with the following:
Replacing SCSI device: /devices/pci@8,700000/scsi@1/sd@3,0
This operation will suspend activity on SCSI bus: c0
Continue (yes/no)?
Enter:
y
The system responds with the following:
SCSI bus quiesced successfully.
It is now safe to proceed with hotplug operation.
Enter y if operation is complete or n to abort (yes/no)?
Enter:
y
Example 5 Encountering a Mounted File System While Unconfiguring a Disk
The following command illustrates encountering a mounted file system
while unconfiguring a disk:
# cfgadm -c unconfigure c1::dsk/c1t0d0
The system responds with the following:
cfgadm: Component system is busy, try again: failed to offline:
/devices/pci@1f,4000/scsi@3,1/sd@1,0
Resource Information
------------------ --------------------------
/dev/dsk/c1t0d0s0 mounted filesystem "/mnt"
Example 6 Displaying the Value of the Locator for a Disk
The following command displays the value of the locator for a disk.
This example is specific to the SPARC Enterprise Server family:
# cfgadm -x locator c0::dsk/c0t6d0
The system responds with the following:
Disk Led
c0t6d0 locator=on
Example 7 Setting the Value of the Locator for a Disk
The following command sets the value of the locator for a disk. This
example is specific to the SPARC Enterprise Server family:
# cfgadm -x locator=off c0::dsk/c0t6d0
The system does not print anything in response.
Example 8 Configuring a Path to a Multipath SCSI Disk
The following command configures a path connected through controller
c0:
# cfgadm -c configure c0::2,0
Example 9 Unconfiguring a Path to a Multipath SCSI Disk
The following command unconfigures a path connected through controller
c0:
# cfgadm -c unconfigure c0::2,0
FILES
/usr/lib/cfgadm/scsi.so.1
hardware-specific library for generic SCSI hot-plugging
/usr/platform/SUNW,SPARC-Enterprise/lib/cfgadm/scsi.so.1
platform-specific library for generic SCSI hot-plugging
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Availabilitysystem/dynamic-reconfiguration
SEE ALSO
config_admin(3CFGADM), libcfgadm(3LIB), scsi_vhci(4D), attributes(7),
cfgadm(8)
NOTES
The disconnect (quiesce) operation is not supported on controllers
which control disks containing critical partitions such as root (/),
/usr, swap, or /var. The disconnect operation should not be attempted
on such controllers. Incorrect usage can result in a system hang and
require a reboot.
When a controller is in the disconnected (quiesced) state, there is a
potential for deadlocks occurring in the system. The disconnect opera‐
tion should be used with caution. A controller should be kept in the
disconnected state for the minimum period of time required to accom‐
plish the DR operation. The disconnect command is provided only to
allow the replacement of the SCSI cables while the system is running.
It should not be used for any other purpose. The only fix for a dead‐
lock (if it occurs) is to reboot the system.
Hotplugging operations are not supported by all SCSI controllers.
WARNINGS
The connectors on some SCSI devices do not conform to SCSI hotplug
specifications. Performing hotplug operations on such devices can cause
damage to the hardware on the SCSI bus. Refer to your hardware manual
for additional information.
Oracle Solaris 11.4 20 Jan 2017 cfgadm_scsi(8)