svcadm(1M)을 검색하려면 섹션에서 1M 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
t_bind(3c)
Standard C Library Functions t_bind(3C)
NAME
t_bind - bind an address to a transport endpoint
SYNOPSIS
#include <xti.h>
int t_bind(int fd, const struct t_bind *req, struct t_bind *ret);
DESCRIPTION
This routine is part of the XTI interfaces that evolved from the TLI
interfaces. XTI represents the future evolution of these interfaces.
However, TLI interfaces are supported for compatibility. When using a
TLI routine that has the same name as an XTI routine, the
tiuser.hheader file must be used. Refer to the TLI COMPATIBILITY sec‐
tion for a description of differences between the two interfaces.
This function associates a protocol address with the transport endpoint
specified by fd and activates that transport endpoint. In connection
mode, the transport provider may begin enqueuing incoming connect indi‐
cations, or servicing a connection request on the transport endpoint.
In connectionless-mode, the transport user may send or receive data
units through the transport endpoint.
The req and ret arguments point to a t_bind structure containing the
following members:
struct netbuf addr;
unsigned qlen;
The addr field of the t_bind structure specifies a protocol address,
and the qlen field is used to indicate the maximum number of outstand‐
ing connection indications.
The parameter req is used to request that an address, represented by
the netbuf structure, be bound to the given transport endpoint. The
parameter len specifies the number of bytes in the address, and buf
points to the address buffer. The parameter maxlen has no meaning for
the req argument. On return, ret contains an encoding for the address
that the transport provider actually bound to the transport endpoint;
if an address was specified in req, this will be an encoding of the
same address. In ret, the user specifies maxlen, which is the maximum
size of the address buffer, and buf which points to the buffer where
the address is to be placed. On return, len specifies the number of
bytes in the bound address, and buf points to the bound address. If
maxlen equals zero, no address is returned. If maxlen is greater than
zero and less than the length of the address, t_bind() fails with
t_errno set to TBUFOVFLW.
If the requested address is not available, t_bind() will return -1 with
t_errno set as appropriate. If no address is specified in req (the len
field of addr in req is zero or req is NULL), the transport provider
will assign an appropriate address to be bound, and will return that
address in the addr field of ret. If the transport provider could not
allocate an address, t_bind() will fail with t_errno set to TNOADDR.
The parameter req may be a null pointer if the user does not wish to
specify an address to be bound. Here, the value of qlen is assumed to
be zero, and the transport provider will assign an address to the
transport endpoint. Similarly, ret may be a null pointer if the user
does not care what address was bound by the provider and is not inter‐
ested in the negotiated value of qlen. It is valid to set req and ret
to the null pointer for the same call, in which case the provider
chooses the address to bind to the transport endpoint and does not
return that information to the user.
The qlen field has meaning only when initializing a connection-mode
service. It specifies the number of outstanding connection indications
that the transport provider should support for the given transport end‐
point. An outstanding connection indication is one that has been passed
to the transport user by the transport provider but which has not been
accepted or rejected. A value of qlen greater than zero is only mean‐
ingful when issued by a passive transport user that expects other users
to call it. The value of qlen will be negotiated by the transport
provider and may be changed if the transport provider cannot support
the specified number of outstanding connection indications. However,
this value of qlen will never be negotiated from a requested value
greater than zero to zero. This is a requirement on transport
providers; see WARNINGS below. On return, the qlen field in ret will
contain the negotiated value.
If fd refers to a connection-mode service, this function allows more
than one transport endpoint to be bound to the same protocol address.
but it is not possible to bind more than one protocol address to the
same transport endpoint. However, the transport provider must also sup‐
port this capability. If a user binds more than one transport endpoint
to the same protocol address, only one endpoint can be used to listen
for connection indications associated with that protocol address. In
other words, only one t_bind() for a given protocol address may specify
a value of qlen greater than zero. In this way, the transport provider
can identify which transport endpoint should be notified of an incoming
connection indication. If a user attempts to bind a protocol address to
a second transport endpoint with a value of qlen greater than zero,
t_bind() will return -1 and set t_errno to TADDRBUSY. When a user
accepts a connection on the transport endpoint that is being used as
the listening endpoint, the bound protocol address will be found to be
busy for the duration of the connection, until a t_unbind(3C) or
t_close(3C) call has been issued. No other transport endpoints may be
bound for listening on that same protocol address while that initial
listening endpoint is active (in the data transfer phase or in the
T_IDLE state). This will prevent more than one transport endpoint bound
to the same protocol address from accepting connection indications.
If fd refers to connectionless mode service, this function allows for
more than one transport endpoint to be associated with a protocol
address, where the underlying transport provider supports this capabil‐
ity (often in conjunction with value of a protocol-specific option). If
a user attempts to bind a second transport endpoint to an already bound
protocol address when such capability is not supported for a transport
provider, t_bind() will return -1 and set t_errno to TADDRBUSY.
RETURN VALUES
Upon successful completion, a value of 0 is returned. Otherwise, a
value of -1 is returned and t_errno is set to indicate an error.
VALID STATES
T_UNBND
ERRORS
On failure, t_errno is set to one of the following:
TACCES The user does not have permission to use the specified
address.
TADDRBUSY The requested address is in use.
TBADADDR The specified protocol address was in an incorrect format
or contained illegal information.
TBADF The specified file descriptor does not refer to a trans‐
port endpoint.
TBUFOVFLW The number of bytes allowed for an incoming argument
(maxlen) is greater than 0 but not sufficient to store the
value of that argument. The provider's state will change
to T_IDLE and the information to be returned in ret will
be discarded.
TOUTSTATE The communications endpoint referenced by fd is not in one
of the states in which a call to this function is valid.
TNOADDR The transport provider could not allocate an address.
TPROTO This error indicates that a communication problem has been
detected between XTI and the transport provider for which
there is no other suitable XTI error (t_errno).
TSYSERR A system error has occurred during execution of this func‐
tion.
TLI COMPATIBILITY
The XTI and TLI interface definitions have common names but use differ‐
ent header files. This, and other semantic differences between the two
interfaces are described in the subsections below.
Interface Header
The XTI interfaces use the header file, xti.h. TLI interfaces should
not use this header. They should use the header:
#include <tiuser.h>
Address Bound
The user can compare the addresses in req and ret to determine whether
the transport provider bound the transport endpoint to a different
address than that requested.
Error Description Values
The t_errno values TPROTO and TADDRBUSY can be set by the XTI interface
but cannot be set by the TLI interface.
A t_errno value that this routine can return under different circum‐
stances than its XTI counterpart is TBUFOVFLW. It can be returned even
when the maxlen field of the corresponding buffer has been set to zero.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ MT LevelSafe
SEE ALSO
t_accept(3C), t_alloc(3C), t_close(3C), t_connect(3C), t_unbind(3C),
attributes(7)
WARNINGS
The requirement that the value of qlen never be negotiated from a
requested value greater than zero to zero implies that transport
providers, rather than the XTI implementation itself, accept this
restriction.
An implementation need not allow an application explicitly to bind more
than one communications endpoint to a single protocol address, while
permitting more than one connection to be accepted to the same protocol
address. That means that although an attempt to bind a communications
endpoint to some address with qlen=0 might be rejected with TADDRBUSY,
the user may nevertheless use this (unbound) endpoint as a responding
endpoint in a call to t_accept(3C). To become independent of such
implementation differences, the user should supply unbound responding
endpoints to t_accept(3C).
The local address bound to an endpoint may change as result of a
t_accept(3C) or t_connect(3C) call. Such changes are not necessarily
reversed when the connection is released.
Oracle Solaris 11.4 7 May 1998 t_bind(3C)