svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
sasinfo(8)
System Administration Commands sasinfo(8)
NAME
sasinfo - Serial Attached SCSI HBA port command line interface
SYNOPSIS
sasinfo hba [-v] [HBA_Name]...
sasinfo hba-port [-lvy] [-a HBA_Name] [HBA_port_nam]...
sasinfo expander [-vt] [-p HBA_port_Name] [Expander_SAS_Addr]...
sasinfo target-port [-s | -v] [Target_port_SAS_Addr]...
sasinfo logical-unit | lu [-v] [device_path]...
sasinfo [-V]
sasinfo [-?]
DESCRIPTION
The sasinfo utility is a command line interface that collects adminis‐
trative information on Serial Attached SCSI-2 (SAS-2) host bus adapter
(HBA) that supports the Storage Management HBA API (SM-HBA). The util‐
ity reports attributes of HBA ports and of expander devices and SCSI
target devices that might be connected to those HBA ports.
sasinfo is implemented as a set of subcommands, described below.
SUB-COMMANDS
The following subcommands are supported by sasinfo.
hba
Lists information for the HBA referenced by the specified HBA_name.
If HBA_name is not specified, all HBAs on the host will be listed.
hba-port
Lists information for the HBA port referenced by the specified
HBA_port_Name. If HBA_port_Name is not specified, all HBA ports on
the host will be listed. Note that HBA ports can be dynamically
configured/unconfigured so that the number of HBA ports on an HBA
can change as connections to target devices are established. With
no connections to a storage device, no HBA port is configured.
expander
Lists hierarchical view of the expander referenced by the specified
Expander_SAS_Addr. If no argument is specified, all expanders that
are visible across all HBA ports on the host will be listed.
target-port
Lists information for those target ports referenced by Tar‐
get_port_SAS_Addr address. If no argument is specified, all target
ports that are visible on the host will be listed.
logical-unit | lu
Lists the logical unit referenced by the specified device_path. If
device_path is not specified, all SAS logical units will be listed,
including the SAS Management Protocol (SMP) target port.
OPTIONS
The following options are supported.
-?, --help
Displays usage information
-a, --hba HBA_Name
Retrieve HBA port information from the HBA_Name of an HBA on the
host. The -a option can only be used with the hba-port subcommand.
-l, --phy-linkstat
Lists the link error statistics information for the phys on the HBA
port referenced by the specified HBA_port_Name or all HBA ports if
no HBA port is specified. This option is used only with the hba-
port subcommand.
-p HBA_port_SAS_Addr, --port HBA_port_SAS_Addr
Retrieve remote port information from the HBA_port_SAS_Addr of the
local HBA port on the host. The -p option can be used only with the
expander subcommand.
-s, --scsi
Lists SCSI attributes for target ports that are requested for dis‐
play. This option is only used for the target-port subcommand.
-v, --verbose
Display details on hardware information, such as SAS address,
topology device, and so forth, based on which subcommand is
invoked.
-V, --version
Displays the version information.
-y, --phy
Lists the phy information on the HBA port specified by
HBA_port_Name or all HBA ports if no HBA port is specified. This
option is used only with the hba-port subcommand.
EXAMPLES
Example 1 Listing All HBAs
The following command lists all HBAs on the host.
# sasinfo hba
HBA Name: SUNW-pmcs-0
HBA Name: SUNW-pmcs-1
Example 2 Listing All HBAs with Details
The following command lists all HBAs on the host, along with related
details. Note that each HBA has two HBA ports configured, with each HBA
port connected to a storage device.
# sasinfo hba -v
HBA Name: SUNW-pmcs-0
Manufacturer: sun
Model: SAS Gen-2
Firmware Version: 1.1
FCode/BIOS Version: 1.1
Serial Number: 111-11111
Driver Name: smvsl
Driver Version: 1.1
Number of HBA Ports: 2
HBA Name: SUNW-pmcs-1
Manufacturer: sun
Model: SAS Gen-2
Firmware Version: 1.1
FCode/BIOS Version: 1.1
Serial Number: 111-11111
Driver Name: smvsl
Driver Version: 1.1
Number of HBA Ports: 2
Example 3 Listing All HBA Ports
The following command lists all HBA ports on the host.
# sasinfo hba-port
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
HBA Port Name: /dev/cfg/c2
HBA Name: SUNW-pmcs-1
HBA Port Name: /dev/cfg/c3
HBA Port Name: /dev/cfg/c4
Example 4 Listing all HBA Ports with Details
The following command lists all HBA ports, with accompanying details.
# sasinfo hba-port -v
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
Type: sas-device
State: online
Local SAS Address: 5000c50000d756aa
Attached Port SAS Address: 50800201a5a502bf
Number of Phys: 4
HBA Port Name: /dev/cfg/c25000c50000d756cc
Type: sas-device
State: online
Local SAS Address: 5000c50000d756aa
Attached Port SAS Address: 50800201a5a503bf
Number of Phys: 4
HBA Name: SUNW-pmcs-1
HBA Port Name: /dev/cfg/c3
Type: sas-device
State: online
Local SAS Address: 5000c50000d756cc
Attached Port SAS Address: 50800201a5a504bf
Number of Phys: 4
HBA Port Name: /dev/cfg/c4
Type: sas-device
State: online
Local SAS Address: 5000c50000d756cc
Attached Port SAS Address: 50800201a5a505bf
Number of Phys: 4
Example 5 Listing phy Information for All HBA Ports
The following command lists phy information for all HBA ports.
# sasinfo hba-port -y
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
Phy Information:
Identifier: 0
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 1
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 2
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 3
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
HBA Port Name: /dev/cfg/c2
Phy Information:
Identifier: 4
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 5
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 6
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 7
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
HBA Name: SUNW-pmcs-1
HBA Port Name: /dev/cfg/c3
Phy Information:
Identifier: 0
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 1
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 2
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 3
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
HBA Port Name: /dev/cfg/c4
Phy Information:
Identifier: 4
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 5
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 6
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Identifier: 7
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Example 6 Listing phy Link Error Statistics for a Specific HBA Port
The following command lists phy link error statistics for a particular
port.
# sasinfo hba-port -ly /dev/cfg/c1
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
Phy Information:
Identifier: 0
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Link Error Statistics:
Invalid Dword: 0
Running Disparity Error: 0
Loss of Dword Sync: 0
Reset Problem: 0
Identifier: 1
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Link Error Statistics:
Invalid Dword: 0
Running Disparity Error: 0
Loss of Dword Sync: 0
Reset Problem: 0
Identifier: 2
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Link Error Statistics:
Invalid Dword: 0
Running Disparity Error: 0
Loss of Dword Sync: 0
Reset Problem: 0
Identifier: 3
State: enabled
HardwareLinkRate(Min/Max): 1.5Gbit/3Gbit
ProgrammedLinkRate(Min/Max): 1.5Gbit/3Gbit
NegotiatedLinkRate: 3Gbit
Link Error Statistics:
Invalid Dword: 0
Running Disparity Error: 0
Loss of Dword Sync: 0
Reset Problem: 0
Example 7 Listing Expanders Connected to an HBA Port
The following command lists all expanders that are visible through the
specified HBA port.
# sasinfo expander -p /dev/cfg/c1
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
Expander SAS Address(Tier 1): 50800201a5a502bf
Expander SAS Address(Tier 2): 50800201a5a50233
Expander SAS Address(Tier 2); 5000c5000d2da812
Expander SAS Address(Tier 1): 50800201a5a503bf
Expander SAS Address(Tier 2): 50800201a5a502d2
Expander SAS Address(Tier 2); 5000c5000d2da823
Example 8 Listing Detailed Information on Expanders
The following command lists detailed information on all expanders that
are visible through the specified HBA port.
# sasinfo expander -v -p /dev/cfg/c1
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
Expander SAS Address(Tier 1): 50800201a5a502bf
OS Device Name: /dev/smp/expd0
State: online
Expander SAS Address(Tier 2): 50800201a5a50233
OS Device Name: /dev/smp/expd2
State: online
Expander SAS Address(Tier 2); 5000c5000d2da812
OS Device Name: /dev/smp/expd3
State: online
Expander SAS Address(Tier 1): 50800201a5a503bf
OS Device Name: /dev/smp/expd1
State: online
Expander SAS Address(Tier 2): 50800201a5a502d2
OS Device Name: /dev/smp/expd3
State: online
Expander SAS Address(Tier 2); 5000c5000d2da823
OS Device Name: /dev/smp/expd4
State: online
Example 9 Listing Target Ports Attached to Expanders
The following command lists all target ports that are attached to
expanders connected to a specified HBA port.
# sasinfo expander -t -p /dev/cfg/c1
HBA Name: SUNW-pmcs-0
HBA Port Name: /dev/cfg/c1
Expander SAS Address(Tier 1): 50800201a5a502bf
Target Port SAS Address: 50800201a5a504f1
Expander SAS Address(Tier 2): 50800201a5a50233
Target Port SAS Address: 50800201a5a502be
Target Port SAS Address: 5000c5000d2da8b2
Expander SAS Address(Tier 2); 5000c5000d2da812
Target Port SAS Address: 50800201a5a502be
Target Port SAS Address: 50800201a5a508b2
Expander SAS Address(Tier 1): 50800201a5a503bf
Target Port SAS Address: 50800201a5a50421
Expander SAS Address(Tier 2): 50800201a5a502d2
Target Port SAS Address: 50800201a5a503be
Target Port SAS Address: 5000c5000d2da7be
Expander SAS Address(Tier 2); 5000c5000d2da823
Target Port SAS Address: 50800201a5a503be
Target Port SAS Address: 5000c5000d2da7be
Example 10 Listing Target Port Information
The following command lists all target ports discovered on the host.
# sasinfo target-port
Target Port SAS Address: 5000c5000bae4009
Target Port SAS Address: 5000c5000baef4b1
Target Port SAS Address: 5000c5000bae3fe1
Target Port SAS Address: 5000c5000bae49d9
Target Port SAS Address: 5000c5000bae36c5
Example 11 Listing Target Port Information with Topology Details
The following command lists all target ports with the HBA port and
expander that they are connected to.
# sasinfo target-port -v
Target Port SAS Address: 5000c5000bae4009
Type: SAS Device
HBA Port Name: /dev/cfg/c7
Expander Device SAS Address: 500e004aaaaaaa3f
HBA Port Name: /dev/cfg/c5
Expander Device SAS Address: 500e004aaaaaaa3f
Target Port SAS Address: 5000c5000baef4b1
Type: SAS Device
HBA Port Name: /dev/cfg/c7
Expander Device SAS Address: 500e004aaaaaaa3f
HBA Port Name: /dev/cfg/c5
Expander Device SAS Address: 500e004aaaaaaa3f
Target Port SAS Address: 5000c5000bae3fe1
Type: SAS Device
HBA Port Name: /dev/cfg/c7
Expander Device SAS Address: 500e004aaaaaaa3f
HBA Port Name: /dev/cfg/c5
Expander Device SAS Address: 500e004aaaaaaa3f
Target Port SAS Address: 5000c5000bae49d9
Type: SAS Device
HBA Port Name: /dev/cfg/c7
Expander Device SAS Address: 500e004aaaaaaa3f
HBA Port Name: /dev/cfg/c5
Expander Device SAS Address: 500e004aaaaaaa3f
Target Port SAS Address: 5000c5000bae36c5
Type: SAS Device
HBA Port Name: /dev/cfg/c7
Expander Device SAS Address: 500e004aaaaaaa3f
HBA Port Name: /dev/cfg/c5
Expander Device SAS Address: 500e004aaaaaaa3f
Example 12 Listing Target Ports with SCSI Information
The following command lists all target port details, including SCSI
information for each target port.
# sasinfo target-port -s 5000c5000bae4009
Target Port SAS Address: 5000c5000bae4009
Type: SAS Device
HBA Port Name: /dev/cfg/c7
Expander Device SAS Address: 500e004aaaaaaa3f
LUN : 0
OS Device Name : /dev/rdsk/c6t5000C5000BAE400Bd0s2
Vendor: Sun
Product: J4400
Device Type: Disk
HBA Port Name: /dev/cfg/c5
Expander Device SAS Address: 500e004aaaaaaa3f
LUN : 0
OS Device Name : /dev/rdsk/c6t5000C5000BAE400Bd0s2
Vendor: Sun
Product: J4400
Device Type: Disk
Example 13 Listing the Logical Units
The following command lists the logical units on a host.
# sasinfo logical-unit
OS Device Name: /dev/rdsk/c4t50020F2300B4904Ed0s2
OS Device Name: /dev/rdsk/c4t50020F230000B4AFd0s2
Example 14 Listing Additional Information on Logical Units
The following command displays additional logical unit information
using the -v option for device /dev/rmt/On.
# sasinfo lu -v
OS Device Name: /dev/rdsk/c4t50020F2300B4904Ed0s2
HBA Port Name: /dev/cfg/c1
Target Port SAS Address: 50020f2300b4904e
LUN: 0
Vendor: Sun
Product: J4400
Device Type: Disk
OS Device Name: /dev/rdsk/c4t50020F230000B4AFd0s2
HBA Port Name: /dev/cfg/c1
Target Port SAS Address: 50020f230063100b
LUN: 0
Vendor: Sun
Product: J4400
Device Type: Disk
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Availabilitysystem/storage/sas-utilities _ Interface
StabilityCommitted
SEE ALSO
attributes(7)
Oracle Solaris 11.4 16 Aug 2011 sasinfo(8)