svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
ipseckey(8)
ipseckey(8) System Administration Commands ipseckey(8)
NAME
ipseckey - manually manipulate an IPsec Security Association Database
(SADB)
SYNOPSIS
ipseckey [-nvp]
ipseckey [-nvp] -f filename
ipseckey -c filename
ipseckey [-nvp] [delete | delete-pair | get] SA_TYPE {EXTENSION value...}
ipseckey [-np] [monitor | passive_monitor | pmonitor]
ipseckey [-nvp] flush [SA_TYPE]
ipseckey [-nvp] dump [SA_TYPE]
ipseckey [-nvp] save SA_TYPE {filename}
ipseckey [-nvp] -s filename
DESCRIPTION
The ipseckey command is used to manually manipulate the security asso‐
ciation databases of the network security services, ipsecah(4P) and
ipsecesp(4P). You can use the ipseckey command to set up security asso‐
ciations between communicating parties when automated key management is
not available.
While the ipseckey utility has only a limited number of general op‐
tions, it supports a rich command language. The user may specify re‐
quests to be delivered by means of a programmatic interface specific
for manual keying. See pf_key(4P). When ipseckey is invoked with no ar‐
guments, it will enter an interactive mode which prints a prompt to the
standard output and accepts commands from the standard input until the
end-of-file is reached. Some commands require an explicit security as‐
sociation ("SA") type, while others permit the SA type to be unspeci‐
fied and act on all SA types.
ipseckey uses a PF_KEY socket and the message types SADB_ADD,
SADB_DELETE, SADB_GET, SADB_UPDATE, SADB_FLUSH, and SADB_X_PROMISC.
Thus, you must have the {PRIV_SYS_IP_CONFIG} privilege or Network IPSec
Management rights profile to use this command.
ipseckey handles sensitive cryptographic keying information. Please
read the Security section for details on how to use this command se‐
curely.
OPTIONS
-c filename
Analogous to the -f option (see following), except that the input
is not executed but only checked for syntactical correctness. Er‐
rors are reported to stderr. This option is provided to debug con‐
figurations without making changes. See SECURITY and "Service Man‐
agement Facility" for more information.
-f filename
Read commands from an input file, filename. The lines of the input
file are identical to the command line language. The load command
provides similar functionality. The -s option or the save command
can generate files readable by the -f argument.
-n
Prevent attempts to print host and network names symbolically when
reporting actions. This is useful, for example, when all name
servers are down or are otherwise unreachable.
-p
Paranoid. Do not print any keying material, even if saving SAs. In‐
stead of an actual hexadecimal digit, print an X when this flag is
turned on.
-s filename
The opposite of the -f option. If '-' is given for a filename, then
the output goes to the standard output. A snapshot of all current
SA tables will be output in a form readable by the -f option. The
output will be a series of add commands, but with some names not
used. This occurs because a single name may often indicate multiple
addresses.
-v
Verbose. Print the messages being sent into the PF_KEY socket, and
print raw seconds values for lifetimes.
COMMANDS
add
Add an SA. Because it involves the transfer of keying material, it
cannot be invoked from the shell, lest the keys be visible in ps(1)
output. It can be used either from the interactive ipseckey> prompt
or in a command file specified by the -f command. The add command
accepts all extension-value pairs described below.
update
Update SA lifetime, and in the cases of larval SAs (leftover from
aborted automated key management), keying material and other exten‐
sions. Like add, this command cannot be invoked from the shell be‐
cause keying material would be seen by the ps(1) command. It can be
used either from the interactive ipseckey> prompt or in a command
file specified by the -f command. The update command accepts all
extension-value pairs, but normally is only used for SA lifetime
updates.
update-pair
As update, but apply the update to the SA and its paired SA, if
there is one.
delete
Delete a specific SA from a specific SADB. This command requires
the spi extension, and the dest extension for IPsec SAs. Other ex‐
tension-value pairs are superfluous for a delete message. If the SA
to be deleted is paired with another SA, the SA is deleted and the
paired SA is updated to indicate that it is now unpaired.
delete-pair
Delete a specific SA from a specific SADB. If the SA is paired with
another SA, delete that SA too. This command requires the spi ex‐
tension and the dest extension for the IPsec SA, or its pair.
get
Lookup and display a security association from a specific SADB.
Like delete, this command only requires spi and dest for IPsec.
flush
Remove all SA for a given SA_TYPE, or all SA for all types.
monitor
Continuously report on any PF_KEY messages. This uses the
SADB_X_PROMISC message to enable messages that a normal PF_KEY
socket would not receive to be received. See pf_key(4P).
passive_monitor
Like monitor, except that it does not use the SADB_X_PROMISC mes‐
sage.
pmonitor
Synonym for passive_monitor.
dump
Will display all SAs for a given SA type, or will display all SAs.
Because of the large amount of data generated by this command,
there is no guarantee that all SA information will be successfully
delivered, or that this command will even complete.
save
Is the command analog of the -s option. It is included as a command
to provide a way to snapshot a particular SA type, for example, esp
or ah.
help
Prints a brief summary of commands.
SA_TYPE
all
Specifies all known SA types. This type is only used for the flush
and dump commands. This is equivalent to having no SA type for
these commands.
ah
Specifies the IPsec Authentication Header ("AH") SA.
esp
Specifies the IPsec Encapsulating Security Payload ("ESP") SA.
EXTENSION VALUE TYPES
Commands like add, delete, get, and update require that certain exten‐
sions and associated values be specified. The extensions will be listed
here, followed by the commands that use them, and the commands that re‐
quire them. Requirements are currently documented based upon the IPsec
definitions of an SA. Required extensions may change in the future.
number can be in either hex (0xnnn), decimal (nnn) or octal (0nnn).
string is a text string. hexstr is a long hexadecimal number with a
bit-length. Extensions are usually paired with values; however, some
extensions require two values after them.
spi number
Specifies the security parameters index of the SA. This extension
is required for the add, delete, get and update commands.
pair-spi number
When pair-spi is used with the add or update commands, the SA being
added or updated will be paired with the SA defined by pair-spi. A
pair of SAs can be updated or deleted with a single command.
The two SAs that make up the pair need to be in opposite directions
from the same pair of IP addresses. The command will fail if either
of the SAs specified are already paired with another SA.
If the pair-spi token is used in a command and the SA defined by
pair-spi does not exist, the command will fail. If the command was
add and the pairing failed, the SA to be added will instead be re‐
moved.
inbound | outbound
These optional flags specify the direction of the SA. When the in‐
bound or outbound flag is specified with the add command, the ker‐
nel will insert the new SA into the specified hash table for faster
lookups. If the flag is omitted, the kernel will decide into which
hash table to insert the new SA based on its knowledge the IP ad‐
dresses specified with the src and dst extensions.
When these flags are used with the update, delete, update-pair, or
get commands, the flags provide a hint as to the hash table in
which the kernel should find the SA.
replay number
Specifies the replay window size. If not specified, the replay win‐
dow size is assumed to be zero. It is not recommended that manually
added SAs have a replay window. This extension is used by the add
and update commands.
replay_value number
Specifies the replay value of the SA. This extension is used by the
add and update commands.
state string|number
Specifies the SA state, either by numeric value or by the strings
"larval", "mature", "dying", or "dead". If not specified, the value
defaults to mature. This extension is used by the add and update
commands.
auth_alg string|number
authalg string|number
Specifies the authentication algorithm for an SA, either by numeric
value, or by strings indicating an algorithm name. Current authen‐
tication algorithms include:
HMAC-SHA-1
sha, sha-1, hmac-sha1, hmac-sha
HMAC-SHA-256
sha256, sha-256, hmac-sha256, hmac-sha-256
HMAC-SHA-384
sha384, sha-384, hmac-sha384, hmac-sha-384
HMAC-SHA-512
sha512, sha-512, hmac-sha512, hmac-sha-512
Often, algorithm names will have several synonyms. This extension
is required by the add command for certain SA types. It is also
used by the update command.
Use the ipsecalgs(8) command to obtain the complete list of authen‐
tication algorithms.
encr_alg string|number
encralg string|number
Specifies the encryption algorithm for an SA, either by numeric
value, or by strings indicating an algorithm name. Current encryp‐
tion algorithms include Triple-DES ("3des"), AES ("aes"), and
Camellia ("camellia"). This extension is required by the add com‐
mand for certain SA types. It is also used by the update command.
Use the ipsecalgs(8) command to obtain the complete list of encryp‐
tion algorithms.
The next six extensions are lifetime extensions. There are two vari‐
eties, "hard" and "soft". If a hard lifetime expires, the SA will be
deleted automatically by the system. If a soft lifetime expires, an
SADB_EXPIRE message will be transmitted by the system, and its state
will be downgraded to dying from mature. See pf_key(4P). The monitor
command to key allows you to view SADB_EXPIRE messages.
idle_addtime number
idle_usetime number
Specifies the number of seconds that this SA can exist if the SA is
not used before the SA is revalidated. If this extension is not
present, the default value is half of the hard_addtime (see below).
This extension is used by the add and update commands.
soft_bytes number
hard_bytes number
Specifies the number of bytes that this SA can protect. If this ex‐
tension is not present, the default value is zero, which means that
the SA will not expire based on the number of bytes protected. This
extension is used by the add and update commands.
soft_addtime number
hard_addtime number
Specifies the number of seconds that this SA can exist after being
added or updated from a larval SA. An update of a mature SA does
not reset the initial time that it was added. If this extension is
not present, the default value is zero, which means the SA will not
expire based on how long it has been since it was added. This ex‐
tension is used by the add and update commands.
soft_usetime number
hard_usetime number
Specifies the number of seconds this SA can exist after first being
used. If this extension is not present, the default value is zero,
which means the SA will not expire based on how long it has been
since it was added. This extension is used by the add and update
commands.
saddr address | name
srcaddr address | name
saddr6 IPv6 address
srcaddr6 IPv6 address
src address | name
src6 IPv6 address
srcaddr address and src address are synonyms that indicate the
source address of the SA. If unspecified, the source address will
either remain unset, or it will be set to a wildcard address if a
destination address was supplied. To not specify the source address
is valid for IPsec SAs. Future SA types may alter this assumption.
This extension is used by the add, update, get, and delete com‐
mands.
daddr address|name
dstaddr address|name
daddr6 IPv6 address|name
dstaddr6 IPv6 address|name
dst addr|name
dst6 IPv6 address|name
dstaddr addr and dst addr are synonyms that indicate the destina‐
tion address of the SA. If unspecified, the destination address
will remain unset. Because IPsec SAs require a specified destina‐
tion address and spi for identification, this extension, with a
specific value, is required for the add, update, get, and delete
commands.
If a name is given, ipseckey will attempt to invoke the command on
multiple SAs with all of the destination addresses that the name
can identify. This is similar to how ipsecconf handles addresses.
If dst6 or dstaddr6 is specified, only the IPv6 addresses identi‐
fied by a name are used.
sport portnum
sport specifies the source port number for an SA. It should be used
in combination with an upper-layer protocol (see below), but it
does not have to be.
dport portnum
dport specifies the destination port number for an SA. It should be
used in combination with an upper-layer protocol (see below), but
it does not have to be.
encap protocol
Identifies the protocol used to encapsulate NAT-traversal IPsec
packets. Other NAT-traversal parameters (nat_*) are below. The only
acceptable value for protocol currently is udp.
proto protocol number
ulp protocol number
proto, and its synonym ulp, specify the IP protocol number of the
SA.
nat_loc address|name
If the local address in the SA (source or destination) is behind a
NAT, this extension indicates the NAT node's globally-routable ad‐
dress. This address can match the SA's local address if there is a
nat_lport (see below) specified.
nat_rem address|name
If the remote address in the SA (source or destination) is behind a
NAT, this extension indicates that node's internal (that is, be‐
hind-the-NAT) address. This address can match the SA's local ad‐
dress if there is a nat_rport (see below) specified.
nat_lport portnum
Identifies the local UDP port on which encapsulation of ESP occurs.
nat_rport portnum
Identifies the remote UDP port on which encapsulation of ESP oc‐
curs.
isrc address | name[/prefix]
innersrc address | name[/prefix]
isrc6 address | name[/prefix]
innersrc6 address | name[/prefix]
proxyaddr address | name[/prefix]
proxy address | name[/prefix]
isrc and innersrc are synonyms. They indicate the inner source ad‐
dress for a tunnel-mode SA.
An inner-source can be a prefix instead of an address. As with
other address extensions, there are IPv6-specific forms to use only
IPv6-specific addresses or prefixes.
Previous versions referred to this value as the proxy address. The
usage, while deprecated, remains.
idst address | name[/prefix]
innerdst address | name[/prefix]
idst6 address | name[/prefix]
innerdst6 address | name[/prefix]
idst and innerdst are synonyms. They indicate the inner destination
address for a tunnel-mode SA.
An inner-destination can be a prefix instead of an address. As with
other address extensions, there are IPv6-specific forms to use only
IPv6-specific addresses or prefixes.
innersport portnum
isport portnum
innersport specifies the source port number of the inner header for
a tunnel-mode SA. It should be used in combination with an upper-
layer protocol (see below), but it does not have to be.
innerdport portnum
idport portnum
innerdport specifies the destination port number of the inner
header for a tunnel-mode SA. It should be used in combination with
an upper-layer protocol (see below), but it does not have to be.
iproto protocol number
iulp protocol number
iproto, and its synonym iulp, specify the IP protocol number of the
inner header of a tunnel-mode SA.
authkey hexstring
Specifies the authentication key for this SA. The key is expressed
as a string of hexadecimal digits, with an optional / at the end,
for example, 123/12. Bits are counted from the most-significant
bits down. For example, to express three '1' bits, the proper syn‐
tax is the string "e/3". For multi-key algorithms, the string is
the concatenation of the multiple keys. This extension is used by
the add and update commands.
encrkey hexstring
Specifies the encryption key for this SA. The syntax of the key is
the same as authkey. A concrete example of a multi-key encryption
algorithm is 3des, which would express itself as a 192-bit key,
which is three 64-bit parity-included DES keys. This extension is
used by the add and update commands.
reserved_bits number
The last number bits of the encrkey string are marked as reserved
in the PF_KEY message. This option is only for testing certain en‐
cryption algorithms.
Certificate identities are very useful in the context of automated key
management, as they tie the SA to the public key certificates used in
most automated key management protocols. They are less useful for manu‐
ally added SAs. Unlike other extensions, srcidtype takes two values, a
type, and an actual value. The type can be one of the following:
prefix
An address prefix.
fqdn
A fully-qualified domain name.
domain
Domain name, synonym for fqdn.
user_fqdn
User identity of the form user@fqdn.
mailbox
Synonym for user_fqdn.
The value is an arbitrary text string that should identify the certifi‐
cate.
srcidtype type, value
Specifies a source certificate identity for this SA. This extension
is used by the add and update commands.
dstidtype type, value
Specifies a destination certificate identity for this SA. This ex‐
tension is used by the add and update commands
Label extensions are used on Trusted Extensions to associate sensitiv‐
ity labels with the traffic carried inside a security association.
These extensions are not allowed unless Trusted Extensions is enabled.
label label
Defines the sensitivity label of traffic carried by this SA. Disal‐
lowed on systems not using Trusted Extensions.
outer-label label
Defines the sensitivity of the ciphertext traffic belonging to this
SA; this label will appear in the outer packet header. Disallowed
on systems not using Trusted Extensions. Incorrect use of this ex‐
tension might allow label policy to be circumvented.
implicit-label label
Defines the sensitivity of the ciphertext traffic belonging to this
SA and request that this SA not contain an explicit on-the-wire la‐
bel. Disallowed on systems not using Trusted Extensions. Incorrect
use of this extension might allow label policy to be circumvented.
Tunnel Mode versus Transport Mode SAs
An IPsec SA is a Tunnel Mode SA if the "proto" value is either 4 (ipip)
or 41 (ipv6) and there is an inner-address or inner-port value speci‐
fied. Otherwise, the SA is a Transport Mode SA.
SECURITY
Keying material is very sensitive and should be generated as randomly
as possible. Some algorithms have known weak keys. IPsec algorithms
have built-in weak key checks, so that if a weak key is in a newly
added SA, the add command will fail with an invalid value.
The ipseckey command allows a privileged user to enter cryptographic
keying information. If an adversary gains access to such information,
the security of IPsec traffic is compromised. The following issues
should be taken into account when using the ipseckey command.
1. Is the TTY going over a network (interactive mode)?
o If it is, then the security of the keying material is
the security of the network path for this TTY's traffic.
Using ipseckey over a clear-text telnet or rlogin ses‐
sion is risky.
o Even local windows might be vulnerable to attacks where
a concealed program that reads window events is present.
2. Is the file accessed over the network or readable to the
world (-f option)?
o A network-mounted file can be sniffed by an adversary as
it is being read.
o A world-readable file with keying material in it is also
risky.
3. The ipseckey command is designed to be managed by the man‐
ual-key smf(7) service. Because the smf(7) log files are
world-readable, the ipseckey does not record any syntax er‐
rors in the log files, as these errors might include secret
information.
If a syntax error is found when the manual-key smf(7) ser‐
vice is enabled, the service enters maintenance mode. The
log file will indicate that there was a syntax error, but
will not specify what the error was.
The administrator should use ipseckey -c filename from the
command line to discover the cause of the errors. See OP‐
TIONS.
If your source address is a host that can be looked up over the network
and your naming system itself is compromised, then any names used will
not be trustworthy.
Security weaknesses often lie in misapplication of tools, not in the
tools themselves. Administrators are urged to be cautious when using
ipseckey. The safest mode of operation is probably on a console or
other hard-connected TTY.
For further thoughts on this subject, see the afterward by Matt Blaze
in Bruce Schneier's Applied Cryptography: Protocols, Algorithms, and
Source Code in C.
Service Management Facility
IPsec manual keys are managed by the service management facility,
smf(7). The services listed below manage the components of IPsec. These
services are delivered as follows:
svc:/network/ipsec/policy:default (enabled)
svc:/network/ipsec/ipsecalgs:default (enabled)
svc:/network/ipsec/manual-key:default (disabled)
svc:/network/ipsec/ike:default (disabled)
The manual-key service is delivered disabled. The system administrator
must create manual IPsec Security Associations (SAs), as described in
this man page, before enabling that service.
The policy service is delivered enabled, but without a configuration
file, so that, as a starting condition, packets are not protected by
IPsec. After you create the configuration file /etc/inet/ipsecinit.conf
and refresh the service (svcadm refresh, see below), the policy con‐
tained in the configuration file is applied. If there is an error in
this file, the service enters maintenance mode. See ipsecconf(8).
Services that are delivered disabled are delivered that way because the
system administrator must create configuration files for those services
before enabling them. See ike.config(5) for the ike service.
See ipsecalgs(8) for the ipsecalgs service.
The correct administrative procedure is to create the configuration
file for each service, then enable each service using svcadm(8).
If the configuration needs to be changed, edit the configuration file
then refresh the service, as follows:
example# svcadm refresh manual-key
Warning: To prevent ipseckey complaining about duplicate Associations,
the ipseckey command flushes the Security Association Data Base (SADB)
when the ipseckey command is run from smf(7), before adding any new Se‐
curity Associations defined in the configuration file. This differs
from the command line behavior where the SADB is not flushed before
adding new Security Associations.
The smf(7) framework will record any errors in the service-specific log
file. Use any of the following commands to examine the logfile prop‐
erty:
example# svcs -l manual-key
example# svcprop manual-key
example# svccfg -s manual-key listprop
The following property is defined for the manual-key service:
config/config_file
This property can be modified using svccfg(8) by users who have been
assigned the following authorization:
solaris.smf.value.ipsec
See auths(1), user_attr(5), rbac(7).
The service needs to be refreshed using svcadm(8) before the new prop‐
erty is effective. General non-modifiable properties can be viewed with
the svcprop(1) command.
# svccfg -s ipsec/manual-key setprop config/config_file = \
/new/config_file
# svcadm refresh manual-key
Administrative actions on this service, such as enabling, disabling,
refreshing, and requesting restart can be performed using svcadm(8). A
user who has been assigned the authorization shown below can perform
these actions:
solaris.smf.manage.ipsec
The service's status can be queried using the svcs(1) command.
The ipseckey command is designed to be run under smf(7) management.
While the ipsecconf command can be run from the command line, this is
discouraged. If the ipseckey command is to be run from the command
line, the manual-key smf(7) service should be disabled first. See sv‐
cadm(8).
EXAMPLES
Example 1 Emptying Out All SAs
To empty out all SA:
example# ipseckey flush
Example 2 Flushing Out IPsec AH SAs Only
To flush out only IPsec AH SAs:
example# ipseckey flush ah
Example 3 Saving All SAs To Standard Output
To save all SAs to the standard output:
example# ipseckey save all
Example 4 Saving ESP SAs To The File /tmp/snapshot
To save ESP SAs to the file /tmp/snapshot:
example# ipseckey save esp /tmp/snapshot
Example 5 Deleting an IPsec SA
To delete an IPsec SA, only the SPI and the destination address are
needed:
example# ipseckey delete esp spi 0x2112 dst 224.0.0.1
An alternative would be to delete the SA and the SAs pair if it has
one:
example# ipseckey delete-pair esp spi 0x2112 dst 224.0.0.1
Example 6 Getting Information on an IPsec SA
Likewise, getting information on a SA only requires the destination ad‐
dress and SPI:
example# ipseckey get ah spi 0x5150 dst mypeer
Example 7 Adding or Updating IPsec SAs
Adding or updating SAs requires entering interactive mode:
example# ipseckey
ipseckey> add ah spi 0x90125 src me.example.com dst you.example.com \
authalg sha1 authkey
ipseckey> update ah spi 0x90125 dst you.example.com hard_bytes \
16000000
ipseckey> exit
Adding two SAs that are linked together as a pair:
example# ipseckey
ipseckey> add esp spi 0x2345 src me.example.com dst you.example.com \
authalg sha1 d3b3be95dd3d688086d06c67c5e28482943142c9 \
encralg aes encrkey be11a84eb75255e0d3add0c0cd9c5315
ipseckey> add esp spi 0x5432 src me.example.com dst you.example.com \
authalg sha1 authkey d3b3be95dd3d688086d06c67c5e28482943142c9 \
encralg aes encrkey be11a84eb75255e0d3add0c0cd9c5315 pair-spi
ipseckey> exit
Example 8 Adding an SA in the Opposite Direction
In the case of IPsec, SAs are unidirectional. To communicate securely,
a second SA needs to be added in the opposite direction. The peer ma‐
chine also needs to add both SAs.
example# ipseckey
ipseckey> add ah spi 0x2112 src you.example.com dst me.example.com \
authalg sha1 authkey
d3b3be95dd3d688086d06c67c5e28482943142c9 \
hard_bytes 16000000
ipseckey> exit
Example 9 Monitoring PF_KEY Messages
Monitoring for PF_KEY messages is straightforward:
example# ipseckey monitor
Example 10 Using Commands in a File
Commands can be placed in a file that can be parsed with the -f option.
This file may contain comment lines that begin with the "#" symbol. For
example:
# This is a sample file for flushing out the ESP table and
# adding a pair of SAs.
flush esp
### Watch out! I have keying material in this file. See the
### SECURITY section in this manual page for why this can be
### dangerous .
add esp spi 0x2112 src me.example.com dst you.example.com \
authalg sha1 authkey d3b3be95dd3d688086d06c67c5e28482943142c9 \
encralg aes encrkey be11a84eb75255e0d3add0c0cd9c5315 \
hard_usetime 28800
add esp spi 0x5150 src you.example.com dst me.example.com \
authalg sha1 authkey d3b3be95dd3d688086d06c67c5e28482943142c9 \
encralg aes encrkey be11a84eb75255e0d3add0c0cd9c5315 \
hard_usetime 28800
## End of file - This is a gratuitous comment
Example 11 Adding SAs for IPv6 Addresses
The following commands from the interactive-mode create an SA to pro‐
tect IPv6 traffic between the site-local addresses
example # ipseckey
ipseckey> add esp spi 0x6789 \
src6 fec0:bbbb::4483 dst6 fec0:bbbb::7843 \
authalg sha1 authkey d3b3be95dd3d688086d06c67c5e28482943142c9 \
encralg aes encrkey be11a84eb75255e0d3add0c0cd9c5315 \
hard_usetime 28800
ipseckey> exit
Example 12 Linking Two SAs as a Pair
The following command links two SAs together, as a pair:
example# ipseckey update esp spi 0x123456 dst 192.168.99.2 \
pair-spi 0x654321
FILES
/etc/inet/secret/ipseckeys
Default configuration file used at boot time. See "Service Manage‐
ment Facility" and SECURITY for more information.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Availabilitysystem/network _ Interface StabilityCommit‐
ted
SEE ALSO
ps(1), svcprop(1), svcs(1), ipsec(4P), ipsecah(4P), ipsecesp(4P),
pf_key(4P), ike.config(5), attributes(7), smf(7), ipsecalgs(8), ipsec‐
conf(8), route(8), svcadm(8), svccfg(8)
Schneier, B., Applied Cryptography: Protocols, Algorithms, and Source
Code in C. Second ed. New York, New York: John Wiley & Sons, 1996.
DIAGNOSTICS
The ipseckey command parses the configuration file and reports any er‐
rors. In the case of multiple errors, ipseckey reports as many of these
as possible.
The ipseckey command does not attempt to use a COMMAND that has a syn‐
tax error. A COMMAND might be syntactically correct but can neverthe‐
less generate an error because the kernel rejected the request made to
pf_key(4P). This might occur because a key had an invalid length or be‐
cause an unsupported algorithm was specified.
If there are any errors in the configuration file, ipseckey reports the
number of valid COMMANDS and the total number of COMMANDS parsed.
Parse error on line N.
If an interactive use of ipseckey would print usage information,
this would print instead. Usually proceeded by another diagnostic.
Because COMMANDS can cover more than a single line in the configu‐
ration file by using the backslash character to delimit lines, its
not always possible to pinpoint in the configuration file the exact
line that caused the error.
Unexpected end of command line.
An additional argument was expected on the command line.
Unknown
A value for a specific extension was unknown.
Address type N not supported.
A name-to-address lookup returned an unsupported address family.
N is not a bit specifier
bit length N is too big for
string is not a hex string
Keying material was not entered appropriately.
Can only specify single
A duplicate extension was entered.
Don't use extension for string for command.
An extension not used by a command was used.
One of the entered values is incorrect: Diagnostic code NN: msg
This is a general invalid parameter error. The diagnostic code and
message provides more detail about what precise value was incorrect
and why.
NOTES
In spite of its IPsec-specific name, ipseckey is analogous to route(8),
in that it is a command-line interface to a socket-based administration
engine, in this case, PF_KEY. PF_KEY was originally developed at the
United States Naval Research Laboratory.
To have machines communicate securely with manual keying, SAs need to
be added by all communicating parties. If two nodes wish to communicate
securely, both nodes need the appropriate SAs added.
In the future ipseckey may be invoked under additional names as other
security protocols become available to PF_KEY.
This command requires sys_ip_config privilege to operate and thus can
run in the global zone and in exclusive-IP zones. The global zone can
set up security associations with ipseckey to protect traffic for
shared-IP zones on the system.
Oracle Solaris 11.4 3 Nov 2021 ipseckey(8)