svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
in.ndpd(8)
in.ndpd(8) System Administration Commands in.ndpd(8)
NAME
in.ndpd - daemon for IPv6 autoconfiguration
SYNOPSIS
/usr/lib/inet/in.ndpd [-adt] [-f config_file]
DESCRIPTION
in.ndpd provides both the host and router autoconfiguration components
of Neighbor Discovery for IPv6 and Stateless and Stateful Address Auto‐
configuration for IPv6. In particular, in.ndpd implements:
o router discovery;
o prefix discovery;
o parameter discovery;
o invocation of stateful address autoconfiguration;
o stateless address autoconfiguration; and
o privacy extensions for stateless address autoconfiguration.
Other aspects of Neighbor Discovery are implemented by ip6(4P), includ‐
ing:
o address resolution;
o neighbor unreachability detection; and
o redirect.
The duplicate address detection function is implemented by the system
kernel.
in.ndpd is managed by the service management facility (SMF), by means
of the service identifier:
svc:/network/routing/ndp:default
If the /etc/inet/ndpd.conf file does not exist or does not set the
variable AdvSendAdvertisements to true for a network interface, then
in.ndpd will make the node a host for that interface, that is, sending
router solicitation messages and then using router advertisement mes‐
sages it receives to autoconfigure the node. Note that in.ndpd only au‐
toconfigures the addresses of global or site-local scope from the pre‐
fix advertisement.
If AdvSendAdvertisements is set to true for an interface, then in.ndpd
will perform router functions on that interface, that is, sending
router advertisement messages to autoconfigure the attached hosts, but
not use any advertisements it receives for autoconfiguration. However,
when sending advertisements, in.ndpd will use the advertisements it
sends itself to autoconfigure its prefixes.
Stateless autoconfiguration requires no manual configuration of hosts,
minimal (if any) configuration of routers, and no additional servers.
The stateless mechanism enables a host to generate its own addresses
and uses local information as well as non-local information that is ad‐
vertised by routers to generate the addresses. in.ndpd will plumb logi‐
cal interfaces for each of these addresses.
Stateful autoconfiguration involves the dhcpagent(8) daemon and the use
of the DHCPv6 protocol. The dhcpagent daemon is responsible for plumb‐
ing the logical interfaces for the acquired addresses, maintaining the
leases, and handling duplicate addresses. in.ndpd starts the dhcpagent
daemon automatically and signals when DHCPv6 should be started. in.ndpd
also detects when dhcpagent configures the logical interfaces, and sets
the appropriate prefix length on each according to received Routing Ad‐
vertisement messages. in.ndpd will not stop dhcpagent; dhcpagent will
exit after a period of time with no leases to manage.
Temporary addresses that are autoconfigured for an interface can also
be implemented. A temporary address token is enabled for one or more
interfaces on a host. However, unlike standard, autoconfigured IPv6 ad‐
dresses, a temporary address consists of the site prefix and a randomly
generated 64 bit number. This random number becomes the interface ID
segment of the IPv6 address. A link-local address is not generated with
the temporary address as the interface ID.
If the kernel detects a duplicate temporary address, in.ndpd will auto‐
matically choose another.
Routers advertise all prefixes that have been assigned on the link.
IPv6 hosts use Neighbor Discovery to obtain a subnet prefix from a lo‐
cal router. Hosts automatically create IPv6 addresses by combining the
subnet prefix with an interface IDs that is generated from an inter‐
face's MAC address. In the absence of routers, a host can generate only
link-local addresses. Link-local addresses can only be used for commu‐
nication with nodes on the same link.
OPTIONS
Supported options and equivalent SMF service properties are listed be‐
low. SMF service properties are set by using the svccfg command, for
example:
# svccfg -s ndp:default setprop key=value
# svcadm refresh
-a
Turn off stateless and stateful address auto configuration. When
set, the daemon does not autoconfigure any addresses and does not
renumber any addresses. This option does the same thing as the fol‐
lowing lines in ndpd.conf(5):
ifdefault StatefulAddrConf off
ifdefault StatelessAddrConf off
Use of this option is equivalent to setting the stateless_addr_conf
property to false.
-d
Turn on large amounts of debugging output on stdout. When set, the
program runs in the foreground and stays attached to the control‐
ling terminal. Use of this option is equivalent to setting the de‐
bug property to true.
-f config_file
Use config_file for configuration information instead of the de‐
fault /etc/inet/ndpd.conf. Use of this option is equivalent to set‐
ting the config_file property to the configuration file to be used.
-t
Turn on tracing (printing) of all sent and received packets tostd‐
out. When set, the program runs in the foreground and stays at‐
tached to the controlling terminal. As such, this option cannot be
run under the SMF.
FILES
/etc/inet/ndpd.conf Configuration file. This file is not necessary
on a host, but it is required on a router to en‐
able in.ndpd to advertise autoconfiguration in‐
formation to the hosts.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Availabilitysystem/network/routing
SEE ALSO
icmp6(4P), ip6(4P), ndpd.conf(5), attributes(7), smf(7), dhcpagent(8),
ipadm(8), svcadm(8)
Narten, T., Nordmark, E., Simpson, W.RFC 2461, Neighbor Discovery for
IP Version 6 (IPv6). The Internet Society. December 1998.
Thomson, S., Narten, T. RFC 2462, IPv6 Stateless Address Autoconfigura‐
tion. The Internet Society. December 1998.
Narten, T., and Draves, R. RFC 3041, Privacy Extensions for Stateless
Address Autoconfiguration in IPv6. The Internet Society. January 2001.
DIAGNOSTICS
Receipt of a SIGHUP signal will make in.ndpd restart and reread
/etc/inet/ndpd.conf.
NOTES
The in.ndpd daemon service is managed by the service management facil‐
ity, smf(7), under the service identifier:
svc:/network/routing/ndp:default
Administrative actions on this service, such as enabling, disabling, or
requesting restart, can be performed by using svcadm(8) command.
Oracle Solaris 11.4 29 Dec 2016 in.ndpd(8)