svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
csplit(1)
csplit(1) User Commands csplit(1)
NAME
csplit - split files based on context
SYNOPSIS
csplit [-ks] [-f prefix] [-n number] file arg1... argn
DESCRIPTION
The csplit utility reads the file named by the file operand, writes all
or part of that file into other files as directed by the arg operands,
and writes the sizes of the files.
OPTIONS
The following options are supported:
-f prefix Names the created files prefix00, prefix01, ..., prefixn.
The default is xx00 ... xxn. If the prefix argument would
create a file name exceeding 14 bytes, an error results.
In that case, csplit exits with a diagnostic message and
no files are created.
-k Leaves previously created files intact. By default, csplit
removes created files if an error occurs.
-n number Uses number decimal digits to form filenames for the file
pieces. The default is 2.
-s Suppresses the output of file size messages.
OPERANDS
The following operands are supported:
file The path name of a text file to be split. If file is -, the
standard input will be used.
The operands arg1 ... argn can be a combination of the following:
/rexp/[offset] Create a file using the content of the lines from the
current line up to, but not including, the line that
results from the evaluation of the regular expression
with offset, if any, applied. The regular expression
rexp must follow the rules for basic regular expres‐
sions. Regular expressions can include the use of
'\/' and '\%'. These forms must be properly quoted
with single quotes, since "\" is special to the
shell. The optional offset must be a positive or neg‐
ative integer value representing a number of lines.
The integer value must be preceded by + or −. If the
selection of lines from an offset expression of this
type would create a file with zero lines, or one with
greater than the number of lines left in the input
file, the results are unspecified. After the section
is created, the current line will be set to the line
that results from the evaluation of the regular
expression with any offset applied. The pattern match
of rexp always is applied from the current line to
the end of the file.
%rexp%[offset] This operand is the same as /rexp/[offset], except
that no file will be created for the selected section
of the input file.
line_no Create a file from the current line up to (but not
including) the line number line_no. Lines in the file
will be numbered starting at one. The current line
becomes line_no.
{num} Repeat operand. This operand can follow any of the
operands described previously. If it follows a rexp
type operand, that operand will be applied num more
times. If it follows a line_no operand, the file will
be split every line_no lines, num times, from that
point.
An error will be reported if an operand does not reference a line
between the current position and the end of the file.
EXAMPLES
Example 1 Splitting and combining files
This example creates four files, cobol00...cobol03.
example% csplit -f cobol filename \
'/procedure division/' /par5./ /par16./
After editing the split files, they can be recombined as follows:
example% cat cobol0[0−3] > filename
This example overwrites the original file.
Example 2 Splitting a file into equal parts
This example splits the file at every 100 lines, up to 10,000 lines.
The -k option causes the created files to be retained if there are less
than 10,000 lines; however, an error message would still be printed.
example% csplit -k filename 100 {99}
Example 3 Creating a file for separate C routines
If prog.c follows the normal C coding convention (the last line of a
routine consists only of a } in the first character position), this
example creates a file for each separate C routine (up to 21) in
prog.c.
example% csplit -k prog.c '%main(%' '/^}/+1' {20}
ENVIRONMENT VARIABLES
See environ(7) for descriptions of the following environment variables
that affect the execution of csplit: LANG, LC_ALL, LC_COLLATE,
LC_CTYPE, LC_MESSAGES, and NLSPATH.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
>0 An error occurred.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Availabilitysystem/core-os _ CSIEnabled _ Interface
StabilityCommitted _ StandardSee standards(7).
SEE ALSO
sed(1), split(1), attributes(7), environ(7), standards(7)
DIAGNOSTICS
The diagnostic messages are self-explanatory, except for the following:
arg − out of range The given argument did not reference a line
between the current position and the end of
the file.
Oracle Solaris 11.4 4 Feb 2015 csplit(1)