svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
ukbd(4)
UKBD(4) BSD Kernel Interfaces Manual UKBD(4)
NAME
ukbd — USB keyboard driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your
kernel configuration file:
device ukbd
Alternatively, to load the driver as a module at boot time, place the
following line in loader.conf(5):
ukbd_load="YES"
DESCRIPTION
The ukbd driver provides support for keyboards that attach to the USB
port. usb(4) and one of uhci(4) or ohci(4) must be configured in the
kernel as well.
CONFIGURATION
By default, the keyboard subsystem does not create the appropriate
devices yet. Make sure you reconfigure your kernel with the following
option in the kernel config file:
options KBD_INSTALL_CDEV
If both an AT keyboard USB keyboards are used at the same time, the AT
keyboard will appear as kbd0 in /dev. The USB keyboards will be kbd1,
kbd2, etc. You can see some information about the keyboard with the fol‐
lowing command:
kbdcontrol -i < /dev/kbd1
or load a keymap with
kbdcontrol -l keymaps/pt.iso < /dev/kbd1
See kbdcontrol(1) for more possible options.
You can swap console keyboards by using the command
kbdcontrol -k /dev/kbd1
From this point on, the first USB keyboard will be the keyboard to be
used by the console.
If you want to use a USB keyboard as your default and not use an AT key‐
board at all, you will have to remove the device atkbd line from the ker‐
nel configuration file. Because of the device initialization order, the
USB keyboard will be detected after the console driver initializes itself
and you have to explicitly tell the console driver to use the existence
of the USB keyboard. This can be done in one of the following two ways.
Run the following command as a part of system initialization:
kbdcontrol -k /dev/kbd0 < /dev/ttyv0 > /dev/null
(Note that as the USB keyboard is the only keyboard, it is accessed as
/dev/kbd0) or otherwise tell the console driver to periodically look for
a keyboard by setting a flag in the kernel configuration file:
device sc0 at isa? flags 0x100
With the above flag, the console driver will try to detect any keyboard
in the system if it did not detect one while it was initialized at boot
time.
DRIVER CONFIGURATION
options KBD_INSTALL_CDEV
Make the keyboards available through a character device in /dev.
options UKBD_DFLT_KEYMAP
makeoptions UKBD_DFLT_KEYMAP=fr.iso
The above lines will put the French ISO keymap in the ukbd driver. You
can specify any keymap in /usr/share/syscons/keymaps or
/usr/share/vt/keymaps (depending on the console driver being used) with
this option.
options KBD_DISABLE_KEYMAP_LOADING
Do not allow the user to change the keymap. Note that these options also
affect the AT keyboard driver, atkbd(4).
SYSCTL VARIABLES
The following variables are available as both sysctl(8) variables and
loader(8) tunables:
hw.usb.ukbd.debug
Debug output level, where 0 is debugging disabled and larger val‐
ues increase debug message verbosity. Default is 0.
FILES
/dev/kbd* blocking device nodes
EXAMPLES
device ukbd
Add the ukbd driver to the kernel.
SEE ALSO
kbdcontrol(1), ohci(4), syscons(4), uhci(4), usb(4), vt(4), config(8)
AUTHORS
The ukbd driver was written by Lennart Augustsson
<augustss@cs.chalmers.se> for NetBSD and was substantially rewritten for
FreeBSD by Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>.
This manual page was written by Nick Hibma <n_hibma@FreeBSD.org> with a
large amount of input from Kazutaka YOKOTA
<yokota@zodiac.mech.utsunomiya-u.ac.jp>.
BSD April 24, 2018 BSD