svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
isp(4)
To compile this driver into the kernel, place the following lines
in your kernel configuration file: Alternatively, to load the
driver as a module at boot time, place the following lines in
isp_load="YES" ispfw_load="YES" This driver provides access to or
SCSI devices. SPI supports initiator mode for Ultra SCSI and
wide mode transactions for Ultra2 LVD (1080, 1280), and Ultra3
LVD (10160, 12160). Fibre Channel supports initiator and target
modes of FCP SCSI profile, utilizing Class 3 and Class 2 (2200
and later) connections. Support is available for Public and Pri‐
vate loops, Point-to-Point and Fabric connections. FC-Tape is
supported on 4Gb (2400) and newer controllers. FC-Tape is highly
recommended for connections to tape drives that support it. It
encompasses four elements from the T-10 FCP-4 specification: Pre‐
cise Delivery of Commands Confirmed Completion of FCP I/O Opera‐
tions Retransmission of Unsuccessfully Transmitted IUs Task Retry
Identification Together these features allow for link level error
recovery with tape devices. Without it, an initiator cannot, for
instance, tell whether a tape write command that has timed out
resulted in all, part or none of the data going to the tape
drive. FC-Tape is automatically enabled when connecting con‐
troller that supports it to a target that supports it. It may be
disabled using configuration and hint options described below.
Firmware loading is supported if the module is loaded. It is
strongly recommended that you use the firmware available from as
it is the most likely to have been tested with this driver.
Cards supported by the driver include: Fast Wide, Ultra Fast Wide
cards, Single Ended or Differential SBus cards. Fast Wide and
Differential Fast Wide SCSI PCI cards. Ultra Wide and Differen‐
tial Ultra Wide SCSI PCI cards. Also known as the DEC KZPBA-CA
(single ended) and KZPBA-CB (HVD differential). LVD Ultra2 Wide
SCSI PCI cards. LVD Ultra3 Wide SCSI PCI cards. Dual Bus Ultra
Wide and Differential Ultra Wide SCSI PCI cards. Dual Bus LVD
Ultra2 Wide SCSI PCI cards. Dual Bus LVD Ultra3 Wide SCSI PCI
cards. Copper and Optical Fibre Channel Arbitrated Loop PCI
cards (single, dual). Copper and Optical Fibre Channel Arbi‐
trated Loop PCI cards (single, dual, quad). Optical 2Gb Fibre
Channel PCI cards. Optical 2Gb Fibre Channel PCI cards. Optical
2Gb Fibre Channel PCI cards (2312 chipset, single and dual at‐
tach). Optical 2Gb Fibre Channel PCIe cards. Dell branded ver‐
sion of the QLogic 2312. Optical 4Gb Fibre Channel PCI cards.
Optical 4Gb Fibre Channel PCIe cards. Optical 8Gb Fibre Channel
PCIe cards. Optical 16Gb FC/FCoE PCIe cards. Optical 16Gb Fibre
Channel PCIe cards. Optical 32Gb Fibre Channel PCIe cards. Tar‐
get mode support for Fibre Channel adapters may be enabled with
the option. To disable FC-Tape, use the following configuration
option: Note that even if the ISP_FCTAPE_OFF option is used, it
may be overridden by the fctape hint described below. The fol‐
lowing options are switchable by setting values in They are: A
hint value to disable loading of firmware A hint value to ignore
board NVRAM settings for. Otherwise use NVRAM settings. A hint
value to set full duplex mode. A hint value to select topology
of connection. Supported values are: Prefer loopback and fall‐
back to point to point. Prefer point to point and fallback to
loopback. Loopback only. Point to point only. This should be
the full 64 bit World Wide Port Name you would like to use, over‐
riding the value in NVRAM for the card. This should be the full
64 bit World Wide Node Name you would like to use, overriding the
value in NVRAM for the card. A hint to override or set the Ini‐
tiator ID or Loop ID. For Fibre Channel cards in Local Loop
topologies it is recommended that you set this value to non-zero.
A hint to define default role for isp instance (0 -- none, 1 --
target, 2 -- initiator, 3 -- both). A hint value for a driver
debug level (see the file for the values. A hint to create spec‐
ified number of additional virtual ports. Set this to 1 to dis‐
able FC-Tape operation on the given isp instance. Set this to 1
to enable FC-Tape operation on the given isp instance for targets
that support it. This value says how long to wait in seconds af‐
ter loop has gone down before giving up and expiring all of the
devices that were visible. The default is 300 seconds (5 min‐
utes). A separate (nonadjustable) timeout is used when booting
to not stop booting on lack of FC connectivity. This value says
how long to wait for devices to reappear if they (temporarily)
disappear due to loop or fabric events. While this timeout is
running, I/O to those devices will simply be held. Setting those
options to 0 allows to disable use of GFF_ID and GFT_ID SNS re‐
quests during FC fabric scan. It may be useful if switch does
not implement them correctly, preventing some devices from being
found. Disabling them may cause unneeded logins to ports not
supporting target role or even FCP at all. The default is 1 (en‐
abled). This is the readonly World Wide Node Name value for this
port. This is the readonly World Wide Port Name value for this
port. The driver was written by originally for NetBSD at
NASA/Ames Research Center. Later improvement was done by The
driver currently ignores some NVRAM settings. Fabric support for
2100 cards has been so problematic, and these cards are so old
now that it is just not worth your time to try it.