svcadm(8)을 검색하려면 섹션에서 8 을 선택하고, 맨 페이지 이름에 svcadm을 입력하고 검색을 누른다.
cfgadm_sata(8)
cfgadm_sata(8) System Administration Commands cfgadm_sata(8)
NAME
cfgadm_sata - SATA hardware-specific commands for cfgadm
SYNOPSIS
/usr/sbin/cfgadm [-f] [-y | -n] [-v] [-o hardware_options]
-c function ap_id...
/usr/sbin/cfgadm [-f] [-y | -n] [-v] [-o hardware_options]
-x hardware_function ap_id...
/usr/sbin/cfgadm [-v] [-a] [-s listing_options]
[-o hardware_options] [-l [ap_id | ap_type]...]
/usr/sbin/cfgadm [-v] [-o hardware_options] -t ap_id...
/usr/sbin/cfgadm [-v] [-o hardware_options] -h [ap_id]...
DESCRIPTION
The SATA hardware specific library, /usr/lib/cfgadm/sata.so.1, provides
the functionality for SATA hot plugging through the cfgadm command. cf‐
gadm operates on attachment points, which are locations in the system
where hardware resources can be dynamically reconfigured. See cfgadm(8)
for information regarding attachment points.
Each SATA controller's and port multiplier's device port is represented
by an attachment point in the device tree. SATA devices, connected and
configured in the system are shown as the attachment point name exten‐
sion. The terms "attachment point" and "SATA port" are used inter‐
changeably in the following description.
Attachment points are named through ap_ids. All the SATA attachment
points ap_id consist of a string in the following form:
sataX/P[.M][::dsk/cXtYd0]
where
X is the SATA controller number
P is the SATA controller's device port number (0 to 31)
M is the port multiplier's device port number (0 to 14) the
port multiplier host port number (15). It is used only
when the port multiplier is attached to the SATA con‐
troller's device port.
dev/cXtYd0 identifies the attached SATA device
Y is a target number
In general, the device identifier is derived from the corresponding
logical link for the device in /dev. Because only one LUN (LUN 0) is
supported by the SATA device, the "d" component of the device string
will always have number 0 (zero).
For example, the logical ap_id of the device port 4 of the port multi‐
plier connected to the device port 5 of the SATA controller 2 would be:
sata2/5.4
If the SATA disk or CD/DVD device is connected to this attachment
point, and the device is configured, the ap_id would be:
sata2/5.4::dsk/c2t645d0
The cXtYd0 string identifying a device has one-to-one correspondence to
the device attachment point.
A simple listing of attachment points in the system will include all
SATA device ports and attached devices. For example:
#cfgadm -l
Ap_Id Type Receptacle Occupant Condition
sata0/0::dev/c0t0d0 disk connected configured ok
sata0/1::dev/c0t1d0 disk connected configured ok
sata0/2::dev/c0t2d0 cd-dvd connected configured ok
sata0/3 sata-port empty unconfigured ok
sata1/0 sata-port disconnected unconfigured unknown
sata1/1 sata port disconnected unconfigured unknown
sata1/2 sata port empty unconfigured ok
sata1/3.15 sata-pmult connected configured ok
sata1/3.0::dev/c0t512d0 disk connected configured ok
sata1/3.1 sata-port empty unconfigured ok
sata1/3.2 sata-port empty unconfigured ok
sata1/3.3 sata-port empty unconfigured ok
usb0/1 unknown empty unconfigured ok
usb0/2 unknown empty unconfigured ok
See cfgadm(8) for more information regarding listing of attachment
points.
The receptacle state for attachment point at the SATA port have the
following meanings:
empty
The SATA port is powered-on and enabled. No device presence was de‐
tected on this port.
disconnected
The SATA port is not enabled or the SATA device presence was de‐
tected but no communication with the device was established, or the
port has failed.
connected
The SATA device is detected on the port the communication with the
device is established.
The occupant (device attached to the SATA port) state have the follow‐
ing meanings:
configured
The attached SATA device is configured and ready to use by the op‐
erating system.
unconfigured
No device is attached, or the SATA device attached to the SATA port
was not yet configured. To configure it, run the command "cfgadm -c
configure ap_id".
The attachment point (SATA port) condition have the following meanings:
ok
The SATA port is powered-on and enabled, and is ready for use.
failed
The SATA port failed. It may be disabled and/or powered-off by the
system. It is unusable and its condition is unknown. It may be due
to the device plugged-in.
unknown
The SATA port is disabled and its condition is unknown.
A "state table" is the combination of an attachment point receptacle
state, an occupant state, and an attachment point (SATA port) condi‐
tion. The valid states are:
empty/unconfigured/ok
The SATA port is enabled and active. No device presence was de‐
tected.
disconnected/unconfigured/ok
The SATA port is enabled and a device presence was detected but no
communications with the device was established.
disconnected/unconfigured/unknown
The SATA Port is disabled and its condition is unknown.
disconnected/unconfigured/failed
The SATA Port is disabled and unusable. The port was disabled by
the system due to a system-detected failure.
connected/unconfigured/ok
The SATA Port is enabled and active. A device presence was detected
and the communication with a device was established. The device is
not configured to be used by the OS.
connected/configured/ok
The device is present and configured, and is ready to use by the
OS.
OPTIONS
cfgadm defines several types of operations besides listing (-l). These
operations include testing, (-t), invoking configuration state changes,
(-c), invoking hardware specific functions (-x), and obtaining configu‐
ration administration help messages (-h).
-c function
The following generic functions are defined for the SATA hardware
specific library. For SATA port attachment point, the following
configuration state change operations are supported:
connect
Enable (activate) the SATA port and establish the communication
with an attached device. This operation implies powering-on the
port if necessary.
disconnect
Unconfigure the attached device, if it is not already unconfig‐
ured, and disable (deactivate) the SATA port. A subsequent
"connect" command enables SATA port operation but does not
bring a device to the "configured" state.
For a SATA device attached to the SATA port following state change
operations are supported:
configure
Configure new device for use by the operating system if it is
not already configured. This command also implies connect oper‐
ation, if necessary.
unconfigure
Unconfigure the device connected to the SATA port if it is not
already unconfigured.
The configure and unconfigure operations cannot be used for an at‐
tachment point where the port multiplier is connected. Port multi‐
pliers are configured and unconfigured automatically by the system.
However, configure and unconfigure operations apply to all SATA de‐
vices connected to the port multiplier's device ports.
-f
Not supported.
-h ap_id
SATA specific help can be obtained by using the help option with
any SATA attachment point.
-l [-v]
The -l option works as described in cfgadm(8). When paired with the
-v option, the "Information" field contains the following SATA-spe‐
cific information:
o Mfg: manufacturer string
o Product: product string
o No: product Serial Number
-o hardware_options
No hardware specific options are currently defined.
-s listing_options
Attachment points of class SATA can be listed by using the select
suboption. See cfgadm(8).
-t ap_id
Perform self-test of the SATA port, if supported by the SATA con‐
troller. If a port self-test operation is not supported by the SATA
controller, an error message is issued.
-x hardware_function
Perform hardware specific function.
Some of the following commands used on the SATA ports or the SATA
controller may affect any SATA devices that have been attached, as
noted. ap_id refers to SATA port or the entire SATA controller, as
noted. If the operation implies unconfiguring a device, but it can‐
not be unconfigured (that is, the device contains a mounted
filesystem), an error message is issued and the operation is not
performed. An error message will be also issued if the SATA con‐
troller does not support specified operation.
sata_reset_device ap_id
Reset the SATA device attached to ap_id SATA port. The SATA
port state does not change.
sata_reset_port ap_id
Reset the SATA port specified by ap_id. If a SATA device is at‐
tached to the port, it is also reset. This operation may be
also performed on the port to which a port multiplier is con‐
nected. If a port multiplier is connected to the SATA con‐
troller port, the SATA devices attached to the port multiplier
may not be reset
sata_reset_all ap_id
Reset SATA controller specified by the controller number part
in ap_id and all attached devices and re-enumerate all con‐
nected devices, including port multipliers and devices con‐
nected to port multipliers' device ports.
This operations implies unconfiguring all attached devices
prior to the operation. Any newly enumerated devices will be
left unconfigured.
sata_port_deactivate ap_id
Force the deactivation of the port when all else fails. This is
meant as an emergency step; use with caution.
sata_port_activate ap_id
Force the activation of a port. This is meant for emergency
situations on a port which was deactivated to recover from er‐
rors.
sata_port_self_test ap_id
Perform self-test operation on the SATA controller. This opera‐
tion implies unconfiguring all devices and resetting the SATA
controller.
-v
Execute in verbose mode.
The following Transitions table reports the state transitions re‐
sulting from the -c operations and hotplugging actions:
current state operation possible new state
------------- --------- ------------------
empty/
unconfigured/ok device plug-in connected/unconfigured/ok, or
disconnected/unconfigured/ok, or
disconnected/unconfigured/failed
empty/
unconfigured/ok -c unconfigure error message, no state change
empty/
unconfigured/ok -c configure error message, no state change
empty/
unconfigured/ok -c connect error message, no state change
empty/
unconfigured/ok -c disconnect disconnected/unconfigured/unknown, or
disconnected/unconfigured/failed
disconnected/
unconfigured/ok device unplug no state change
disconnected/
unconfigured/ok -c unconfigure error message, no state change
disconnected/
unconfigured/ok -c configure error message, no state change
disconnected/
unconfigured/ok -c connect error message, no state change
disconnected/
unconfigured/ok -c disconnect error message, no state change
disconnected/
unconfigured/
unknown
(no disk plugged) -c configure error message, state change to
empty/unconfigured/ok, or
disconnected/unconfigured/failed
disconnected/
unconfigured/
unknown -c configure state change to
(disk plugged) connected/configured/ok or,
connected/unconfigured/ok, or
disconnected/unconfigured/failed and
possible error message
disconnected/
unconfigured/
unknown -c connect empty/unconfigured/ok, or
connected/unconfigured/ok, or
disconnected/unconfigured/ok, or
disconnected/unconfigured/unknown, or
disconnected/unconfigured/failed
disconnected/
unconfigured/
unknown -c disconnect error message, no state change
disconnected/
unconfigured/
failed any command error message, no state change
other than
-x commands
connected/
unconfigured/ok disk unplug error message and state:
empty/unconfigured/ok, or
disconnected/unconfigured/failed
connected/
unconfigured/ok -c configure connected/unconfigured/ok, or
connected/configured/ok, or
disconnected/unconfigured/ok, or
disconnected/unconfigured/failed
connected/
unconfigured/ok -c unconfigure error message, no state change
connected/
unconfigured/ok -c connect error message, no state change
connected/
unconfigured/ok -c disconnect disconnected/unconfigured/unknown, or
disconnected/unconfigured/failed
connected/
configured/ok disk unplug error message and state:
empty/unconfigured/ok, or
disconnected/unconfigured/failed
connected/
configured/ok -c configure error message, no state change
connected/
configured/ok -c unconfigure error message, if device cannot be
unconfigured, no state change, or
connected/unconfigured/ok, or
disconnected/unconfigured/ok, or
disconnected/unconfigured/failed
connected/
configured/ok -c connect error message, no state change
connected/
configured/ok -c disconnect error message, if device cannot be
unconfigured, no state change, or
disconnected/unconfigured/unknown, or
disconnected/unconfigured/failed
EXAMPLES
Example 1 Configuring a Disk
The following command configures a disk attached to SATA controller 0,
port 0:
example# cfgadm -c configure sata0/0
This command should be issued only when there is a device connected to
the SATA port.
Example 2 Unconfiguring a Disk
The following command unconfigures a disk attached to SATA controller
0, port 3:
example# cfgadm -c unconfigure sata0/3
The device identifying string is shown when the attachment point recep‐
tacle state is "connected" and occupant state is "configured".
Example 3 Encountering a Mounted File System While Unconfiguring a Disk
The following command illustrates encountering a mounted file system
while unconfiguring a disk:
example# cfgadm -c unconfigure sata1/5
The system responds with the following:
cfgadm: Component system is busy, try again: failed to offline:
/devices/pci@0,0/pci8086,244e@1e/pci1095,3124@1/sd@5,0
Resource Information
------------------ --------------------------
/dev/dsk/c1t5d0s0 mounted filesystem "/mnt"
FILES
/usr/lib/cfgadm/sata.so.1
Hardware specific library for generic SATA hot plugging.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
tab() box; cw(2.75i) |cw(2.75i) lw(2.75i) |lw(2.75i) ATTRIBUTE TYPEAT‐
TRIBUTE VALUE _ Architecturex86 _ Availabilitysystem/dynamic-reconfigu‐
ration
SEE ALSO
config_admin(3CFGADM), libcfgadm(3LIB), attributes(7), cfgadm(8)
NOTES
The emergency "sata_port_deactivate" operation is not supported on
ports with attached disks containing critical partitions such as root
(/), /usr, swap, or /var. The deactivate operation should not be at‐
tempted on such ports. Incorrect usage can result in a system hang and
require a reboot.
Hotplugging operations are not supported by all SATA controllers.
If SATA connectors are the hot-pluggable type and the SATA controller
supports hotplugging, a SATA device can be hotplugged at any time. The
system detects the event and establishes the communication with the de‐
vice. The device has to be configured by the explicit "cfgadm -c con‐
figure ap_id" command.
If the SATA connectors are the hot-pluggable type and the SATA con‐
troller supports hotplugging, unplugging a device without unconfiguring
it may result in system hang or data loss. If a device is unconfigured
but receptacle state is not in a disconnected state, unplugging a de‐
vice from the SATA port will result in error message.
WARNINGS
The connectors on some SATA devices do not conform to SATA hotplug
specifications. Performing hotplug operations on such devices can cause
damage to the SATA controller and/or the SATA device.
Oracle Solaris 11.4 14 Jun 2023 cfgadm_sata(8)